Total : 0

Dòng ISOTHANE 3000 - Loại thông

Tên Hạng mụcThuốc nhựa TPU polyesther Loại thông
Đặc tính sản phẩm ISOTHANE® 3000 series resins are polyether based thermoplastic polyurethane. They exhibit excellent mechanical properties, hydrolytic resistance, fungus resistance, and low temperature performance properties. ISOTHANE® 3000 series can be processed by extrusion and injection molding.
Trường hợp sử dụng Apparel Applications And Outdoor Applications.
Tên Hạng mụcThuốc nhựa TPU polyesther Loại thông
Description ISOTHANE 3000 series resins are polyether based thermoplastic polyurethane. They exhibit excellent mechanical properties, hydrolytic resistance, fungus resistance, and low temperature performance properties. ISOTHANE 3000 series can be processed by extrusion and injection molding.
Supply and Storage ISOTHANE TPU resins are supplied in pellet form packed in 25kg moisture proof bags. All TPU resins have been dried before packing. ISOTHANE TPU resins should be stored in cool and dry environment in their original containers until be used. Storage temperature should not exceed 30°C. If only a portion of TPU resins was used from a bag, the remainder of TPU resins should be tightly closed.
Drying TPU resins are hygroscopic and pre-drying of TPU resins is always a necessary step before processing. Depend on the climate, the granule exposed to the atmosphere will absorb moisture very quickly. The moisture might bring about partial degradation of polymers and the formation of bubbles or streaks in the molded and extruded parts. In order to ensure the efficient and successful processing into quality parts, the moisture content in TPU resins is recommended less than 0.02%.

A desiccant-bed-type hopper dryer is recommended for drying ISOTHANE TPU. The dew point of the inlet air should be in the range of -30 to -40°C. About the recommended drying conditions, please view ISOTHANE individual data sheets.
Processing - Extrusion Barrel and Motor
  • High torque drive capacity at low speed
  • Vented or standard barrels acceptable
Screw
  • Compression ratios between 2:1 and 3:1
  • Minimum L/D of 30/1
Feed Throat
  • Vertical and tangential
  • Water cooling is recommended
Screen Pack
  • Streamlined breaker plates with screen packing is recommended
  • Typical 40/80/80/40 mesh screens
Die
  • Streamline with good temperature control
  • Land Length is generally 10 to 15 times the part thickness
  • Coat-hanger manifold-type dies are recommended for extruding film and sheet
  • Crosshead dies are recommended for wire, cable and hose jacketing
  • Side-fed rotating dies are recommended for blown film
About the recommended extrusion temperatures, please view ISOTHANE individual data sheets.
Processing - Injection Molding Barrel and Motor
  • High torque drive capacity at low speed
  • Vented or standard barrels acceptable
Screw
  • Compression ratios between 2:1 and 3:1
  • Metering screw with gradual transition zone
Injection Pressure
  • Typical 6,000 to 15,000 psi
  • Hold pressure 60 – 70% of forward time
Injection speed
  • Slow to moderate
  • Depends on gating, wall section and flow length
About the recommended injection molding temperatures, please view ISOTHANE individual data sheets.
Coloring Generally, ISOTHANE TPU resins are supplied in their natural color. They can be colored by blending with pigment or pigment master batch. Using master batch based on TPU is recommended. Other master batch based on polyethylene or polystyrene is suitable to a limited extent. All colorants employed in TPU resins must be pre-dried before processing.

The normal addition of pigment or pigment master batch is 0.2%-0.5% or 1-3%.
Additives Various additives can be used to enhanced the properties of ISOTHANE TPU resins, e.g. anti-blocking agents, antioxidant, UV stabilizers or release agents. Most additives supplied as master batches are available. But not all additives are compatible with ISOTHANE TPU resins. It is recommended to inquire of your suppliers or our technical service before compounding.
Recycling For ISOTHANE TPU resins, up to 20% of regrind may be recycled with virgin material depending on finished parts requirements. The regrind material has to be kept free of contamination, diced and dried before re-using. The material which has been contaminated, discolored or degraded is not suitable for recycling. TPU resins may decrease desired properties, e.g. hardness and mechanical properties, due to improperly mixing with regrind.
Regulatory or testing organizations (e.g., UL) may have specific requirements limiting the allowance amount of regrind. Certain quality requirements laid down in specifications may exclude the use of regrind material.
Healthy and Safety Information Before working with these products, it is essential that all operators are aware of the healthy and safety precautions. ISOTHANE TPU resins can be processed or machined over a wide range of temperature. There can be some smoke formation during processing. The smoke that contains some decomposition substances of TPU or additives may cause irritation to human body. Generally, the temperature does not exceed 240°C that can reduce decomposition formation. An effective extraction system, especially in the melt outlet zone, is necessary. The detail information concerning healthy and safety can be available in safety data sheets (SDS) or contact our technical service.
Disposal ISOTHANE TPU resins present no hazard to the environment or water. They can be dumped on municipal landfill or in a waste incineration plant. The official regulations on waste disposal should be observed.
Hạng mụcUnitsASTM3065A3075A3080AU3085AU3090AU
Tỷ trọng   D-792 1.08 1.11 1.13 1.13 1.15
Độ cứng Shore A  D-2240 65A 73A 80A 85A 90A
Độ mạnh kháng kéo MPa
psi
D-412 30
4400
21
3000
30
4400
37
5400
54
7800
Tỷ lệ kéo dài @ 50%  số lượng màng kháng kéo MPa
psi
D-412 2
280
3
440
5
725
4.5
650
8
1200
Tỷ lệ kéo dài @ 100%  số lượng màng kháng kéo MPa
psi
3
370
4
560
7
1020
5.9
850
10
1450
Tỷ lệ kéo dài @ 300%  số lượng màng kháng kéo MPa
psi
5
740
6
850
10
1450
12
1700
15
2200
Tỷ lệ kéo dài bị đứt % D-412 730 930 750 600 550
Độ cứng xé rách N/mm
lb/in
D-624
DIE C
69
390
86
490
110
630
110
600
120
680
Hạng mụcUnitsASTM3095AU3055D3060D3065D3070DU-W
Tỷ trọng   D-792 1.15 1.16 1.17 1.17 1.20
Độ cứng Shore A D D-2240 93A 55D 60D 65D 70D
Độ mạnh kháng kéo MPa
psi
D-412 52
7500
47
6800
45
6500
52
7500
70
10000
Tỷ lệ kéo dài @ 50%  số lượng màng kháng kéo MPa
psi
D-412 12
1800
13
1900
13
1900
24
2400
60
8800
Tỷ lệ kéo dài @ 100%  số lượng màng kháng kéo MPa
psi
15
2100
17
2450
19
2800
28
4100
62
9000
Tỷ lệ kéo dài @ 300%  số lượng màng kháng kéo MPa
psi
23
3400
31
4500
32
4700
41
6000
-
-
Tỷ lệ kéo dài bị đứt % D-412 570 430 400 400 260
Độ cứng xé rách N/mm
lb/in
D-624
DIE C
136
780
150
850
150
850
240
1400
500
2900

Tất cả các số liệu liệt kê trong bảng trên chỉ dùng tham khảo.

Dòng ISOTHANE 3000F - Loại dùng cho thực phẩm

Tên Hạng mụcThuốc nhựa TPU polyesther FDA Loại dùng cho thực phẩm
Đặc tính sản phẩm ISOTHANE® 3000 series resins are polyether based thermoplastic polyurethane. They exhibit excellent mechanical properties, hydrolytic resistance, fungus resistance, and low temperature performance properties. ISOTHANE® 3000 series can be processed by extrusion and injection molding.
Trường hợp sử dụng Apparel Applications And Outdoor Applications.

proimages/thumb/image-cHJvZHVjdA==--product1473751561592131.png

Liên hệ